Datalogic C-BOX 300 Manual de instalación

C-BOX 300/310Installation Manual

C-BOX 300/310 678 59 42 3 1 10 Figure D - Bottom Inside Power on switch 1 2 Scanner grounding selector 3 Spring clamp terminal blocks5 4 GET b

SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT - This product is intended to be installed by Qua

Terminating Resistors Terminating resistors must be used if the C-BOX is installed at the beginning or end of the PROFIBUS cable segment. In this c

GENERAL FEATURES 1 1 GENERAL FEATURES 1.1 DESCRIPTION The C-BOX 3X0 is a connection box which converts RS232 communications to Profibus. It is avai

C-BOX 300/310 2 2 INSTALLATION 2.1 PACKAGE CONTENTS Verify that the C-BOX 3X0 and all the parts supplied with the equipment are present and intact

INSTALLATION 2 2.2 OPENING THE DEVICE To install the C-BOX 3X0 or during normal maintenance, it is necessary to open it by unscrewing the four cover

C-BOX 300/310 2 2.3 MECHANICAL INSTALLATION The diagram below gives the overall dimensions of the C-BOX 3X0 and may be used for its installation.

INSTALLATION 2 C-BOX 3X0 can be installed to operate in different positions. The two screw holes inside the housing of the C-BOX 3X0 are for mechanica

C-BOX 300/310 2 2.4 ELECTRICAL CONNECTIONS AND HARDWARE SETUP The following figure shows the typical layout. PROFIBUS MASTERC-BOX 3X0SCANNERSystem

INSTALLATION 2 NOTE Autoconnection is not compatible with Matrix readers and must be disabled in the C-BOX 3x0 configuration. See par. 2.9 for detail

C-BOX 300/310 2 NOTE Pin 1 is also electrically connected to pins 3 and 5, just as pin 2 is electrically connected to pins 4 and 6. This is useful f

INSTALLATION 2 2.4.2 System Wiring The connection and wiring procedure for C-BOX 3X0 is described as follows: 1) Open the C-BOX 3X0 as described in

C-BOX 300/310 2 The C-BOX 3X0 spring clamp connector pinouts are indicated in the following table. Refer to the scanner Installation Manual for deta

INSTALLATION 2 2.4.3 Scanner Chassis Grounding Jumper Settings The scanner chassis grounding method can be selected by positioning a jumper (see Fig

C-BOX 300/310 2 2.5 PROFIBUS CONNECTIONS AND SETUP 2.5.1 Profibus Node Address Selection To interface the C-BOX 3X0 with a Profibus network, the

INSTALLATION 2 9-pin external female connector pinout Pin Name Function 1 N.C. not connected 2 N.C. not connected 3 B-LINE (RS485+) 4 RTS Ready T

C-BOX 300/310 2 To ensure that the C-BOX functions without errors, the shield of the PROFIBUS cable must be grounded. – Ensure that the PROFIBUS con

INSTALLATION 2 2.6 CONFIGURATION SWITCH AND 9-PIN INTERNAL CONNECTOR The 9-pin internal connector may have two different functions according to the

C-BOX 300/310 2 POSITION MODE CFG: When the switch is in this position, the C-BOX 3X0 is in configuration mode. The communication with the scanner i

INSTALLATION 2 2.7 SCANNER REQUIREMENTS The C-BOX 3X0 can be connected to the following scanners through the 25-pin connector illustrated in Figure A

C-BOX 300/310 INSTALLATION MANUAL

C-BOX 300/310 2 2.8.1 GET/TEST/SEND Functions The C-BOX 300 has three internal function buttons. In the C-BOX 310, they are also available on the co

INSTALLATION 2 GET – (left button): the C-BOX 3X0 reads the current scanner configuration and permanently copies it in its own memory support (EEPROM

C-BOX 300/310 2 2.8.2 LED Indicators Figure 15 - LED Indicators TX LED MS LEDs Warning LED BUS activity Power on In the C-BOX 3X0 the Warning LE

INSTALLATION 2 The internal LEDs of the C-BOX 3X0 (see Figure 15) indicate the following: POWER ON (PWR) (red) indicates the C-BOX 3X0 is connected

C-BOX 300/310 2 2.9 SPECIAL NOTES FOR MATRIX READER SETUP CAUTION When connected to a C-BOX 3x0 through the 25-pin connector, the 9-pin Auxiliary

INSTALLATION 2 2.9.2 Matrix Reader Configuration Using VisiSet™ After performing C-Box 3x0 configuration as described in the previous paragraph, the

C-BOX 300/310 2 Figure 18 – WinHost Configuration Menu for C-Box 3x0 6. Close the C-BOX 300. 24

TECHNICAL FEATURES 3 3 TECHNICAL FEATURES ELECTRICAL FEATURES C-BOX 300 C-BOX 310 Power Supply voltage 10 to 30 Vdc Power consumption max. 2.9 W

DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy 05 dichiara che declares that the déclare que le bescheinigt, daß das

DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy C-BOX 300/310 Ed.: 03/2006 ALL RIGHTS

CONTENTS GUIDE TO INSTALLATION ... iv GENERAL VIEW ...

GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the C-BOX 3X0. 1)

GENERAL VIEW C-BOX 300 23 41 Figure A 25-pin scanner connectorCover screws (4)Compression connectors123Profibus connector4 v

C-BOX 310 2 1 Figure B LCD displayKeypad12 vi

C-BOX 300/310 32 1 865 4 7 Figure C - Cover Inside LCD contrast trimmer* 1 2 Power on LED 3 BUS activity LED 4 Tx LED 5Module status LEDs 678C