Datalogic DX8200A-3010 Manual de instalación Pagina 34
- Pagina / 139
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DX8200A REFERENCE MANUAL
18
3
NOTE
To avoid electromagnetic interference when the scanner is connected to a
CBX connection box, verify the jumper positions in the CBX as indicated in
its Installation Manual.
3.1 POWER SUPPLY
Vdc models:
Power can be supplied to the scanner through the CBX100/500 spring clamp terminal pins
as shown in Figure 6:
V+
in
Earth
Ground
Power Supply
VGND
Figure 6 - Power Supply Connections
The power must be between 20 and 30 Vdc only. The max. power consumption is 30 W
including startup current.
Several accessory power supplies are available to power the DX8200A Vdc models and
reading station components. See par. 1.7.
A security system allows the la
ser to activate only once the motor has reached the correct
rotational speed; consequently, the laser beam is generated after a slight delay from the
power on of the scanner.
It is recommended to connect the device CHASSIS to earth ground (Earth) by setting the
appropriate jumper in the CBX connection box. See the CBX Installation Manual for details.
Vac models:
The supply voltage for correct operation of the scanner must be between 110 and 240 VAC.
The max. power consumption is 48 VA including startup current.
24 Vdc is generated and available on the 26-pin connector and can be used to power
external devices through a correctly jumpered CBX100/CBX500, i.e. photocell, etc. This
voltage however cannot be used to propagate power for a Lonworks network.
A security system allows the laser to activate only once the motor has reached the correct
rotational speed; consequently, the laser beam is generated after a slight delay from the
power on of the scanner.
- Reference Manual 1
- CONTENTS 3
- REFERENCES 6
- COMPLIANCE 7
- POWER SUPPLY 8
- CE COMPLIANCE 9
- FCC COMPLIANCE 9
- GENERAL VIEW 10
- GUIDE TO INSTALLATION 13
- 1 INTRODUCTION 17
- DX8200A - 3 X Y Z 19
- 1.5 KEYPAD AND DISPLAY 20
- 1.5.1 Internal Net 20
- 1.5.2 Test Mode 21
- 1.5.3 PackTrack (Auto) 21
- USING SCANNER MENU 22
- 1.6.3 Auto PackTrack Setup 24
- INTRODUCTION 25
- 1.7 ACCESSORIES 27
- Fieldbus) 28
- 2 INSTALLATION 29
- 2.2 MECHANICAL MOUNTING 30
- 2.2.1 Mounting the Scanner 30
- INSTALLATION 31
- CBX ELECTRICAL CONNECTIONS 33
- 3.1 POWER SUPPLY 34
- 3.2 MAIN SERIAL INTERFACE 35
- Function 36
- Multidrop Cable 39
- Reference 40
- USER INTERFACE 40
- MEP-593 PH-1 Photocell (PNP) 42
- OEK-1 Encoder (PNP) 43
- In put De vi ce (Enc oder) 43
- 9-pin male connector 48
- 25-pin male connector 48
- 4.1 POWER SUPPLY 50
- 4.2 MAIN SERIAL INTERFACE 51
- 4.2.1 RS232 Interface 52
- 4.3 AUXILIARY INTERFACE 56
- 4.4 INPUTS 56
- EXTERNAL TRIGGER/ENCODER 57
- 4.4.1 Code Verifier 59
- 4.5 OUTPUTS 59
- DX8200A USER INTERFACE 60
- 4.6 USER INTERFACE 61
- 5 LONWORKS CONNECTIONS 62
- 5.1 NETWORK TERMINATION 63
- 5.2 LONWORKS INTERFACE 64
- LONWORKS CONNECTIONS 65
- 6 FIELDBUS CONNECTIONS 66
- FIELDBUS CONNECTIONS 67
- 6.3 DEVICENET INTERFACE 69
- 6.4 PROFIBUS INTERFACE 70
- 7 TYPICAL LAYOUTS 71
- TYPICAL LAYOUTS 73
- Minimum Distance 75
- 7.1.3 Redundant System 76
- 7.1.4 Multidata Network 78
- 7.1.5 Fieldbus Networks 79
- 8 SOFTWARE CONFIGURATION 81
- Test Operating Mode 82
- On Line Operating Mode 83
- Automatic Operating Mode 83
- Net-Autoset 86
- Express Network Setup 86
- Network Wizard 87
- SOFTWARE CONFIGURATION 89
- 8.4 PARAMETER DEFAULT VALUES 92
- 9 READING FEATURES 97
- 9.2 PACKTRACK™ 98
- PackTrack™ Reference System 99
- DX8200A REFERENCE MANUAL 100
- READING FEATURES 101
- Auto PackTrack Setup 103
- Auto PackTrack Report 106
- Scanner Direction 108
- PS Offset 109
- 9.3 PERFORMANCE 112
- 9.3.1 Reading Conditions 113
- 9.4 READING DIAGRAMS 115
- 10 MAINTENANCE 119
- 11 TROUBLESHOOTING 121
- 12 TECHNICAL FEATURES 124
- TECHNICAL FEATURES 125
- A ALTERNATIVE LAYOUTS 126
- Fieldbus 127
- Network 127
- PASS THROUGH 129
- RS232 MASTER/SLAVE 130
- MULTIPLEXER 132
- GLOSSARY 133
- DECLARATION OF CONFORMITY 138
Relacionado con productos y manuales para Lectores De Códigos De Barras Datalogic DX8200A-3010
(2 paginas)
(20 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales